How to Install Street Scene Front Chin Spoiler - Unpainted on your Mustang

VERY IMPORTANT! Read and understand all directions and check the following parts list before starting installation.

1. After the front lip spoiler is prepped and painted, double sided tape should be applied to the indentation on the inside of the front spolier. This surface has to be CLEAN and DRY for the tape to properly adhere. A residual free cleaner is recommended (e.g. Wurth Clean Solve) to prepare the surface. The surface of the vehicle should also be prepped and cleaned to for proper adhesion. For best results after cleaning use the adhesion promoter provided to the areas where the tape will be used. When applying tape, make sure the tape is smooth and wrinkle free. It is best to use the multiple small pieceson the long section rather than 1 long piece.

2. After applying the tape pul back approximately 1 inch of the protective covering from the tape on each end. Make sure the film is sticking out. Place the front lip spoiler GENTLY on the vehicle and make sure you have it positioned correctly. It is good to have someone help you with this. Remember when using adhesion promoter you will not get a second chance! So make sure it is on correctly. While holding it in position, pull the tabs you created while applying light downward pressure. Continue this taking care not to tear off the tabs by pulling to hard. After all the film is removed, apply frim pressure all around to insure the tape has bonded properly .

3. Use the provided self tapping screws to secure the back of the spoiler onto the vehicle.

4. Done! Enjoy you brand new front lip spoiler!

STREET SCENE URETHANE PAINT PREPERATION
PROPER PAINTING TECHNIQUES FOR POLY URETHANE PRODUCTS

ALL PARTS SHOULD BE PROFESSIONALLY PAINTED

Pre-fit the component to vehicle. Once you are assured that you have the right component you may proceed, we highly recommend using masking tape anywhere the component may be touching the vehicle body to prevent scratches during the pre-fit.

1. The first step will help to remove pinholes and bubbles that form in the poly urethane. First use a 220 grit sand paper with a DA sander. Sand part complete.

2. Next clean part with aerosol cleaner ( wax & grease remover ).

3. Spray booth: Prime part complete. ( Use PCL 905 primer ).

4. Once part is dry, sand with 320 DA sander. To finish the part wet sand entire part with 400 grit sand paper by hand. This will' give the part a nice finish before painting it.

5. Clean part again.

6. Spray booth: Next spray sealer, Use DP 48 ( PPG white sealer ). Do this to make the part white before painting it. With the part still in the spray booth then finish painting the part with the factory matched color, and then finish with clear coat. ( Use PPG 2010 clear ).

7. Neat color sand / wet sand the part. First use 1000 grit wet / dry sand paper and sand any dirt or runs out. Then go over the entire part with 1500. Last go over the part with 2000. Sand mostly the smooth and flat surfaces, trying to stayaway from the edges so that you do not burn ( go through the painted surface) it laterusing the buffer.

8. Next buff it with a rubbing compound, and finish it with polish. Wash the surface and you will have a beautifully finished part.

ON ALL THE SSE URETHANE PARTS THE PREFERRED PROCEDURES ARE :

A. Pre-fit, sand and shape
B. Paint
C. Install

IMPORTANT PAINT PREP INSTRUCTIONS

URETHANE PAINTING INSTRUCTIONS

Urethane body components require a special cleaning and painting procedure to obtain a proper finish. Once the urethane components have been properly pre-filled CLEAN AND SCRUB THEM Using plenty of hot water, plenty of scouring powder ( Like AJAX Or COMET and a # 7447 Scotch Brite Pad ). Scrub each piece thoroughly until there are no shiny spots. Scrub all surfaces expecially the back side top sections that will be against the body. You will be applying double sided tape to this area so clean and sand it !. The goal is to achieve an even dull finish on all surfaces to be painted. After you've finished scrubbing the parts completely repeat the procedure one more time. If this is not done properly the paint will not stick.

Any automotive primer will provide excellent adhesion to the part if the surface is properly prepared. how ever ! WE DO NOT RECOMMEND USING LACQUER PRIMER ON URETHANE COMPONENTS DUE TO IT'S RIGIDITY. Elastomeric of acrylic primers can be used but elastomeric primers due to the flex agent added are preferred over acrylic primers. Light sanding is recommended after primer has dried and before final color painting.

STREET SCENE BODY
COMPONENT INSTALL PROCEDURE

1. TEST FIT: Make sure you have the proper component BEFORE Proceding further.

2. PRE-FIT: Sand, Shape, Fill as necessary

3. PAINT: Following paint prep procedure outlined above .